Process: How does SUP23T use the cleaning function?

本文适用SUP23T清洗模式

This paper is suitable for SUP23T cleaning mode.

1.切换清洗程序：通过首页右上角的切换按钮，切换程序，断电重启

Switch the cleaning program: Switch the program through the switch button in the upper right corner of the home page, and restart after power failure.

2.更换适合的聚焦镜：不同焦距的镜片清洗幅度不一样，请根据机型所能用的提示选择

Replace the appropriate focusing lens: the cleaning range of lenses with different focal lengths is different, please choose according to the tips available for the model.

3.拿掉枪头前的锁紧部分

SUP23T需在侧边松开锁紧螺丝才可能拿出夹头

Remove the locking part in front of the gun head.

SUP23T needs to loosen the locking screw at the side to take out the chuck.

①清洗工艺

cleaning process

扫描频率：电机的摆动速度，范围10-100Hz，建议设置80

扫描宽度：光斑的扫描宽度，取决于您的机型使用的镜片规格，并在系统设置里选择

峰值功率：一般默认为激光器最大功率

占空比：默认100%

脉冲频率：默认2000

设置参数后，导入并返回，即可在首页的左侧看到此工艺

Scanning frequency: swing speed of motor, ranging from 10 Hz to 10-100Hz, 80 is recommended.

Scanning width: the scanning width of the light spot depends on the lens specifications used by your model and is selected in the system settings.

Peak power: generally, it defaults to the maximum power of the laser.

Duty cycle: 100% by default

Pulse frequency: 2000 by default.

After setting the parameters, import and return, and you can see this process on the left side of the home page.

②焦点的确认

Confirmation of focus

通过来回近远距离的扫描，在声音最大，火花最大时即为焦点，此时应按照这个距离进行清洗，能量最强

根据使用聚焦的不同，以下做参考

F150聚焦（一般枪头到板材的距离为10-15厘米左右能量最强）

F400聚焦（一般枪头到板材的距离为35-40厘米左右能量最强）

F800聚焦（一般枪头到板材的距离为75-85厘米左右能量最强）

By scanning back and forth for a long distance, the focus is when the sound is the loudest and the spark is the biggest. At this time, cleaning should be carried out according to this distance, and the energy is the strongest.

According to the use of focusing, the following is a reference.

F150 focusing (generally, the distance from the gun head to the plate is about 10-15cm, and the energy is the strongest).

F400 focusing (generally, the distance from the gun head to the plate is about 35-40 cm, and the energy is the strongest).

F800 focusing (generally, the distance from the gun head to the plate is about 75-85cm, and the energy is the strongest).

③气体的使用

清洗的气体选择：空气不低于3公斤，三级以上过滤无油无水或使用其他惰性气体

Use of gas

Selection of gas for cleaning: air is not less than 3kg, and oil-free and water-free or other inert gases are used for filtering above the third level.

清洗时请保持枪头到板材的距离平稳，手速保持均匀

When cleaning, please keep the distance between the gun head and the plate stable and the hand speed uniform.