Technology: the realization of fish scale pattern

鱼鳞纹的实现有两种

There are two ways to realize fish scale lines.

一.通过系统的自带的点焊功能

Through the system's own spot welding function

二.送丝机脉冲送丝（超强伟业带脉冲功能的送丝机）

Pulse wire feeder (Super Weiye wire feeder with pulse function)

一.使用点焊功能实现

Using spot welding function to realize

1.1 首页启用点焊模式

home page enables spot welding mode.

1.2 设置里面选择点焊的类型（鱼鳞纹）

Set the type of spot welding (fish scale pattern) selected inside.

1.3 设置里面设置合理的点焊持续时间和点焊间隔时间

Set the reasonable spot welding duration and spot welding interval inside.

（在此模式下，间断时只关激光，其他设置的参数如开关/关光时间不影响也不生效，所以保护镜损坏量会上升）

(In this mode, only the laser is turned off when it is interrupted, and other set parameters, such as on/off time, do not affect or take effect, so the damage of the protective mirror will increase.)

只需设置点焊持续时间和间隔时间即可产生鱼鳞纹焊接效果，最低可设置1ms）

You only need to set the duration and interval of spot welding to produce the fish-scale welding effect, and the minimum can be set to 1ms)

例

点焊持续时间：150ms（此参数影响焊接的纹状大小）

点焊间隔时间：50ms（此参数影响两个纹状之间的间隔）

example

Duration of spot welding: 150ms (this parameter affects the size of welding grain)

Spot welding interval: 50ms (this parameter affects the interval between two stripes).

间断模式焊接

Intermittent mode welding

（在此模式下，间断时关激光、关保护气体、停止送丝。其他设置的参数如开关/关光时间影响也生效，。主要用于定长焊接）

(In this mode, the laser, protective gas and wire feeding are turned off intermittently. Other set parameters, such as switching on/off time, also take effect. Mainly used for fixed-length welding)

通过设置点焊持续时间来改变焊接长度，点焊间隔时间可设高一些

By setting the duration of spot welding to change the welding length, the interval of spot welding can be set higher.

例

点焊持续时间：1000ms（此参数影响焊接长度，也就是出光的时间）

点焊间隔时间：5000ms（此参数可固定数值，默认为5000）

请注意，在此模式下，断丝的时候需要人为的判定，及时上抬断丝

example

Spot welding duration: 1000ms (this parameter affects the welding length, that is, the time of light emission).

Spot welding interval: 5000ms (this parameter can be fixed, and the default is 5000).

Please note that in this mode, the broken wire needs to be judged manually and lifted in time.

二.送丝机脉冲送丝（超强伟业带脉冲功能的送丝机）

Pulse wire feeder (Super Weiye wire feeder with pulse function)

系统不做变更，正常的焊接模式下，通过送丝机切换到脉冲模式，设置脉冲周期和平滑度

The system does not change. In normal welding mode, switch to pulse mode through wire feeder, and set pulse period and smoothness.