超期伟业焊接头的清洗参数设置一.系统的接线清洗版接线与焊接版没有差别,可参考其接线部分:SUP20S说明书‍(信号接口一的5/6脚短接,使其安全地锁有效,扣动扳机按钮后即出光)二.工艺设置Cleaning parameter setting of extended welding jointI. Wiring of the systemThere is no difference b...
一.铜嘴的使用铜嘴的分类主要区分:是否送丝,焊丝的大小,焊接角度,如上图所示,如内角送丝焊接1.0的焊丝则使用AS-12的铜嘴The classification of the copper nozzle is mainly divided into: whether the wire is fed, the size of the welding wire, and the welding...
焊接时遵循以下原则①板材越厚,焊丝越粗,功率越大,送丝速度越慢②功率越低,焊接面越白,功率越大,焊缝从彩色变黑色,此时单面成形。③焊丝的粗细选择应不大于板厚偏向于板厚,焊丝影响焊缝的饱满程度④焊丝越细,扫描宽度越低受不同品牌激光器影响,以下工艺使用下列激光器打样测试,仅供参考,使用时需要适当微调①热刺/创鑫/杰普特②氩气Follow the following principles when...
一.参数的设置首页的焊接模式选择:连续,并设置工艺,调整好需要的焦点I. Parameter settingHome welding mode selection: continuous, and set the process, adjust the required focus二.信号的检测只有【激光器扳机信号】和【安全地锁信号】有效时,才会出光(激光器状态正常),同时首页未出现任何报警...
超强伟业焊接头的切割设置Cutting setup for super weld head一.铜嘴使用切割铜嘴(建议铜嘴1.5以上)One. Copper tipUse cutting copper tip (recommended copper tip 1.5 or more)二.工艺Ii. Process与焊接不同的是,切割光斑是没有宽度的,因此扫描宽度务必设置为0,即红光为一个点其他参...
点焊功能对应的面板监测页版本号为:330以上(含)The version number of the panel monitoring page corresponding to the spot welding function is: 330 or above (inclusive)一. 如何使用点焊功能 1.1 首页启用点焊模式1.2 设置里面选择点焊的类型(鱼鳞纹/间断)1.3 设置...
当出现【监测】页面显示不对,且接线没问题的时候,或者开关电源灯闪烁的时候,可以按照这个来处理When the [Monitoring] page is not displayed correctly, and the wiring is fine, or when the switching power supply light flashes, you can follow this to...
本文适用以下问题表现:This document applies the following issues:1.在不扣动扳机的时候,扳机信号常亮1. When the trigger is not pulled, the trigger signal is always on2.在安全地锁未接触到工件时,安全地锁常亮2. When the safety lock does not touch...
表现:Manifestation: 首页出现电机过热,无法焊接The home page shows that the motor is overheating and cannot be welded原因分析:Cause analysis: 热敏没插好或损坏The thermal is not plugged in or damaged故障处理(两种方案可选任意一个):Troubles...
表现:Manifestation:焊接枪与工件接触时,检测页【安全地锁信号】显示为灰色When the welding gun is in contact with the workpiece, the inspection page [Safety locksignal] is grayed out原因分析:Cause analysis: 焊接枪与工件接触时,信号接口一的5/6脚应导通状...
表现:Manifestation:扣动扳机按钮时,检测页【激光器扳机信号】显示为灰色When the trigger button is pulled, the detection page [Laser Trigger Signal] is grayed out原因分析:Cause analysis: 扣动扳机时,信号接口一的7/8脚应导通状态,当出现断路或主板内部问题,则显示为灰色,结...
表现:Manifestation: 焊接状态时,扣动扳机后,出气送丝,红光正常可见,但是不出激光In the welding state, after pulling the trigger, the gas is fed, and the red light is normally visible, but the laser is not out原因分析:Cause analysis:...
表现:Manifestation: 送丝轮间后堵丝Wire plugging after feeding wheels原因分析:Cause analysis: 由于在此结构后阻力很高,导致无法送丝在送丝轮卡住,应解决阻力问题Due to the high resistance behind this structure, the inability to feed the wire st...
表现:Manifestation: 短时间内保护镜损坏出现烧点,保护镜出光面有点状损坏点,呈现黑色或白色中黑点In a short period of time, the protective mirror is damaged and the burning point appears, and the protective mirror is a little damaged poin...
表现:Manifestation:焊接状态时,出关断续,并且送丝/出气断续In the welding state, the outlet is intermittent, and the wire feed/gas outlet is intermittent原因分析:Cause analysis: 扳机按钮信号或者安全地锁信号丢失The trigger button signal or ...
原因分析:Cause analysis: 焊接过程中,有热量扩散到铜嘴致使损坏,处理过程应首先分析热量来源,镜片散光,红光偏还是外部材料导热During the welding process, there is heat diffusion to the copper nozzle to cause damage, the treatment process should first a...
问题现象:Problem phenomenon:通电后焊接头尾部电机出现啸叫/摆动红光异常/发热/无法调整摆动宽度After powering on, the welding head and tail motor has a howling sound/swing red light abnormality/heat/unable to adjust the swing width问题原因...
正常光斑通过摆动电机变成一条光斑线(左),如果当电机不摆动了,那么就会显示一个点出来(右)The normal spot becomes a spot line (left) by swinging the motor, and if the motor does not swing, then a dot will be displayed (right)原因分析:一.软件部分是否设置正确...
运行逻辑:送丝机通过尾部的两芯插头信号线,接到控制盒的信号接口二的5/6脚,系统运行时控制盒主板内置继电器吸合后5/6导通,送丝机开始工作(即5/6脚控制通断) Operation logic: the wire feeder is connected to the 5/6 pin of the signal interface two of the control box t...
表现:Manifestation: 开始出光很强,慢慢变弱/光弱,导致无法熔丝或铜嘴处有火花The light is strong at first, and slowly weakens/weakens, resulting in the inability to fuse or sparks at the copper nozzle原因分析:Cause analysis: 通常情况下...
Handheld welding: Dynamic parameter protocol功能用于机器人通讯,直接修改调用内部参数本协议兼容 Modbus RTU 规范。The function is used for robot communication, which directly modifies the internal parameters of the callThis Agr...
本文阐述更换送丝机主板操作,适用所有机型送丝机主板的更换1.更换前的准备请务必在断电情况下更换操作2.更换方法This article describes the operation of replacing the main board of the wire feeder, which is applicable to the replacement of the main board ...
因单摆电机,只可以软件调整红光左右(微调),不可以软件调整上下,因此在特殊情况,需要使用机械调整Because the pendulum motor can only be adjusted around the red light by software (fine tuning), it can not be adjusted up and down by software, so in...
水管及气管接口可安装外径6MM内径4MM的软管。中间为气路进,两边为水路的进出管路(不分进出方向),如下图所示:Hose with an outer diameter of 6MM and an inner diameter of 4MM can be installed on the water pipe and gas pipe interface. The middle is the ...
超强焊接系统的授权功能,可对设备进行使用时长授权,当设备使用超过其设定的时间,则显示授权终止1.拍摄检测页面或检测界面的设备编号发送给售后人员,告知需要加密多久(解密方法一致),我司发送一个密码The authorization function of the super welding system can authorize the use time of the equipment, ...
(如果您已经获得了带有程序的SD卡,可直接跳到最后2.3进行刷机操作)一.刷程序前的准备1.1.内存卡(容量在16G以下,过大将会导致刷程序异常)(内存卡的选择请与售后提前沟通,不同的版本区分SDHC大卡或小卡)1.2.专用读卡器(USB转SD的都可以)(If you already have an SD card with the program, you can skip to the ...
注意:be careful:1.更换时请注意现场环境,建议使用纸胶带防尘1.Please pay attention to the on-site environment during replacement, and it is recommended to use paper tape to prevent dust2.保护镜密封圈规格为:15*21*2.7Specification o...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用纸胶带防尘1.Please pay attention to the on-site environment during replacement, and it is recommended to use paper tape to prevent dust2.保护镜密封圈规格为:15*21*2.7Specification o...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用密封胶带防护更换Please pay attention to the on-site environment during replacement, and it is recommended to use sealing tape for protection and replacement2.聚焦镜密封圈为:15*21*2....
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用纸胶带防尘1.Please pay attention to the on-site environment during replacement, and it is recommended to use paper tape to prevent dust2.保护镜密封圈规格为:15*21*2.7Specification o...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用密封胶带防护更换Please pay attention to the on-site environment during replacement, and it is recommended to use sealing tape for protection and replacement2.聚焦凸面朝下(即安装后朝向保护镜...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用密封胶带防护更换Please pay attention to the on-site environment during replacement, and it is recommended to use sealing tape for protection and replacement2.聚焦凸面朝下(即安装后朝向保护镜...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意:be careful:1.更换时请注意现场环境,建议使用纸胶带防尘1.Please pay attention to the on-site environment during replacement, and it is recommended to use paper tape to prevent dust2.保护镜密封圈规格为:26*34*2.7Specification o...
注意:be careful:1.更换时请注意现场环境,建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
本文阐述版本号为411的软件说明,您可以通过监测页面查看系统版本后三位新增:诊断功能、监测界面重构This article describes the software description with version 411. You can view the last three parts of the system version through the monitoring pag...
本文阐述版本号为550的软件说明,您可以通过监测页面查看系统版本后三位This article describes the software description for version 550. You can view the last three parts of the system version through the monitoring page①此界面可以看到当前工艺参数...
本文阐述版本号为306的软件说明,您可以通过设置页面查看系统版本后三位This document describes the software version 306. You can view the last three digits of the system version on the Settings page在此页面可以直接调整送丝速度,通过上下键调整1.首页数值显示送丝速度,...
本文阐述版本号为342的软件说明,您可以通过监测页面查看系统版本后三位This article describes the software description for version 342. You can view the last three parts of the system version through the monitoring page①此界面可以看到当前工艺参数...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please ensure that the laser icon in the article is the same model as the laser you are using2. If the laser manufacturer'...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please ensure that the laser icon in the article is the same model as the laser you are using2. If the laser manufacturer'...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号 本文适用 YLR-14 型号2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please make sure that the laser icon in the article is the same model as the laser you are using2. If the l...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please ensure that the laser icon in the article is the same model as the laser you are using2. If the laser manufacturer'...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号 本文适用 YDFL-1000-CW 光纤激光器2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please ensure that the laser diagram in the article is the same model as the laser you use. This a...
注意:1.请确保文中的激光器图示与您使用的激光器为同一型号 本文适用 FCA1000/FCA1500型号2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线Attention:1. Please ensure that the laser icon in the article is the same model as the laser you are using. This...
一.控制盒的接线定义控制盒提供了必要的硬线信号接口,根据激光器的说明书提供的定义匹配接线,以SUP20S手持焊接为例One. Wiring definition of the control boxThe control box provides the necessary hard-wired signal interface to match the wiring according t...